COMPETENCE 8 – Appropriate Use of Hand Tools, Machine Tools and Measuring Instruments for Fabrication and Repair on Board
Results
Congratulations! Share the result.
Try again. There is always a chance. Review the results.
#1. The number of screw threads per inch for a Standard National Coarse 1/2 inch bolt is:
Incorrect!
#2. Tapping threads into a blind hole should be finished by using a:
Incorrect!
#3. The characteristic of a good quality lubricating oil for use in any machinery should be:
Incorrect!
#4. If your ship burns 8 tons of fuel per hour at 15 knots, how many tons per hour will it burn at 21 knots?
Incorrect!
#5. How many BTUs must be added to one pound of water at 32°F to raise the temperature to 212°F?
Incorrect!
#6. Safety valve gags should only be installed hand tight in order to prevent:
Incorrect!
#7. If the main propulsion diesel governor works irregularly with a jerking motion, a possible cause can be:
Incorrect!
#8. If the thimble of a micrometer were turned through one complete revolution, the micrometer would open or close by a linear distance of:
Incorrect!
#9. If your ship burns 8 tons of fuel per hour at 15 knots, how many tons per hour will it burn at 20 knots?
Incorrect!
#10. Persistent knocking in one cylinder of an eight cylinder diesel engine would MOST likely be caused by.
Incorrect!
#11. If a centrifugal pump vibrates and is noisy when operating, the cause could be:
Incorrect!
#12. If your ship burns 8 tons of fuel per hour at 15 knots, how many tons per hour will it burn at 18 knots?
Incorrect!
#13. In terms of linear measurement, approximately how many “inches” equal one “meter”?
Incorrect!
#14. If your ship burns 8 tons of fuel per hour at 15 knots, how many tons per hour will it burn at 19 knots?
Incorrect!
#15. Lube oil contamination will increase due to normal wear of engine components as a result of:
Incorrect!
#16. If your ship burns 5 tons of fuel per hour at 23 knots, how many tons per hour will it burn at 18 knots?
Incorrect!
#17. If your vessel burns 8 tons of fuel per hour at 15 knots, how many tons per hour will it burn at 19 knots?
Incorrect!
#18. The blade for a power hacksaw should be installed with the teeth:
Incorrect!
#19. If your ship burns 8 tons of fuel per hour at 15 knots, how many tons per hour will it burn at 22 knots?
Incorrect!
#20. The chemical analysis of an oil sample taken form the main propulsion machinery indicates a report of an increase neutralization number, you should be aware that:
Incorrect!
#21. If a stateroom has a 6" by 12" opening through which air travels at 100 feet per minute, what is the volume of air being supplied to the stateroom?
Incorrect!
#22. Leakage over the ends of the blade tips, as a result of the pressure differential between each row of blades in a reaction turbine, can be reduced with a blade design known as.
c
#23. If your vessel burns 4 tons of fuel per hour at 21 knots, how many tons per hour will it burn at 16 knots?
Incorrect!
#24. If your ship burns 3 tons of fuel per hour at 19 knots, how many tons per hour will it burn at 15 knots?
Incorrect!
There are 24 questions for the actual examination for Competence 8 for OIC-EW with a passing rate of 70%. This means that you are only allowed to make 7 mistakes.
DISCLAIMER
The questionnaires contained in this “reviewer” are extracted from the post released by MARINA on their official website and other review materials. Please note that Seaman Kowts is not affiliated with, endorsed by, or connected to the official website of MARINA. The information provided on this website is for general informational and educational purposes only and should not be relied upon as official or authoritative. If you require official information or services, please visit the official website or any relevant review center. We do not assume any responsibility or liability for any consequences resulting from the use of information or services provided on this website.
